Compressors
Part Number | Description | SW Frame |
MW Frame |
W-7 Frame |
W-6 Frame |
---|---|---|---|---|---|
906-004 | Adapter Tool | X | X | ||
914-691 | Bearing Shell Remover | X | X | X | |
939-926 | Bearing Shell Remover | X | |||
S-8384 | Compressor Rod Nut Bar | X | X | X | X |
935-351 | Crosshead Nut Wrench | X | X | X | |
909-975 | Extension Tool | X | X | X | X |
906-003 | Handle for Crosshead | X | X | X | |
906-021 | Handle for Crosshead | X | |||
939-940 | Puller, Compressor Piston | X | |||
939-978 | Starter, Piston Rod – 2 ½” | X | X | ||
904-923 | Starter, Piston Rod – 2 ¼” | X | |||
904-925 | Starter, Piston Rod – 2 ¼” | X | |||
904-925-003 | Starter, Piston Rod – 2 ½” | X | |||
937-391 | Socket, 3” Flats | X | X | X | X |
S-8228 | Socket, 3” Hex | X | X | X | X |
906-005 | Socket, 1 ¾” | X | X | ||
939-938 | Socket, 1 ¼” | X | |||
909-973 | T-Handle | X | X | X | |
909-971 | T-Handle | X | X | X | X |
909-977 | Valve Disassembly Tool | X | X | X | X |
919-541 | Valve Ring Clamp | X | X | X | X |
917-041 | Valve Remover | X | X | X | X |
917-042 | Valve Remover | X | |||
937-391 | Wrench, Piston Rod | X | X | X | X |
S-8676 | Wrench, Compressor Nut (12 pt) | X | X | X | X |
939-994 | Wrench, Piston Rod 2 ½” | X |
![]() |
Crosshead Nut Wrench 935-351 For removing and installing individual cylinder heads. Attaches directly and quickly to the tapped holes in the cylinder head. No tools are required. The two lifting holes will position the head either level for the inline engines or at an angle for the vee engines. |
![]() |
Rod Insertion Tool 939-978 This tool is used to install the compressor rod into packing without damaging the seals. This tool is used only on SW frames. |
![]() |
Rod Insertion Tool 904-923 This tool is used to install the compressor rod into packing without damaging the seals. This tool is used only on W-6 frames. |
![]() |
Rod Insertion Tool 904-925 This tool is used to install the compressor rod into packing without damaging the seals. This tool is used only on MW frames. |
![]() |
Rod Insertion Tool 904-925-003 This tool is used to install the compressor rod into packing without damaging the seals. This tool is used only on W-7 frames. |
![]() |
Main Bearing Removal Tool 914-691 Sized to fit in the oil hole of the main bearing journal of the crankshaft. Care must be taken to roll the crankshaft in the correct direction; i.e. not against the bearing tang. This will damage the bearing. This tool can be used on SW and MW compressor frames. |
![]() |
Main Bearing Removal Tool 939-926 Sized to fit in the oil hole of the main bearing journal of the crankshaft. Care must be taken to roll the crankshaft in the correct direction; i.e. not against the bearing tang. This will damage the bearing. This tool can be used on W-7 and W-6 compressor frames. |
![]() |
Handle for Crosshead 906-003 This tool is used to install and remove the crosshead from the crosshead guide. It comes in quantities of two that can be bolted together for storage. |
![]() |
Handle for Crosshead 906-021 This tool is used to install and remove the crosshead from the crosshead guide. It comes in quantities of two that can be bolted together for storage. |
![]() |
Adapter Tool 906-004 |
![]() |
Socket 906-005 |
![]() |
Wrench, Piston Rod 937-391 |
![]() |
Extension Tool 909-975 This tool is used to pull the valve chairs from the cylinders. |
![]() |
T Handle 909-973 This handle is used to pull the valves from the cylinders. |
![]() |
T Handle 909-971 This handle is used to pull the valves from the cylinders. |
![]() |
Valve Disassembly Tool 909-977 |
![]() |
Valve Ring Clamp 919-541 |
![]() |
Valve Remover 917-041 This tool is used to pull the valve from the cylinder with the threaded female end. |
![]() |
Valve Remover 917-042 This tool is used to pull the valve from the cylinder with the threaded female end. |
![]() |
Puller, Compressor Piston 939-940 |
![]() |
Socket 939-938 |
![]() |
Socket, 3″ Hex S-8228 Socket with 3” internal hex used to loosen/tighten compressor rod piston nuts with 3” standard hex. |
![]() |
Socket, 3″ Flats 937-391 Socket with 3” internal flats used to loosen/tighten compressor rod piston nuts with 3” flats. |
![]() |
Compressor Rod Nut Bar S-8384 Used to break the compressor rod nuts loose. Bar is heat treated carbon steel. One end fits in 1” dia hole, other end fits in 1.06” dia hole. |
![]() |
Wrench, Compressor Nut (12 pt) S-8676 4” hex-12 pt wrench used to grip the compressor rod nut better. |
![]() |
Wrench, Piston Rod 2 ½” 939-994 Used to loosen/tighten compressor rod from crosshead. |
Part Number | Description | MH | WH |
---|---|---|---|
906-004 | Adapter Tool | X | X |
600-329-001 | Adapter, Valve Remover | X | X |
914-691 | Bearing Shell Remover | X | X |
S-8384 | Compressor Rod Nut Bar | X | X |
935-351 | Crosshead Nut Wrench | X | X |
909-975 | Extension Tool | X | X |
939-926 | Main Bearing Removal Tool | X | X |
620-116-001 | Protector, Rod | X | X |
939-940 | Puller, Compressor Piston | X | X |
909-973 | T-Handle | X | X |
909-971 | T-Handle | X | X |
600-306 | Valve Puller | X | X |
S-8676 | Wrench, Compressor Nut (12 pt) | X | X |
![]() |
Compressor Rod Nut Bar S-8384 Used to break the compressor rod nuts loose. Bar is heat treated carbon steel. One end fits in 1” dia hole, other end fits in 1.06” dia hole. |
![]() |
Wrench, Compressor Nut (12 pt) S-8676 4” hex-12 pt wrench used to grip the compressor rod nut better. |
![]() |
Adapter Tool 906-004 |
![]() |
T-Handle 909-973 This handle is used to pull the valves from the cylinders, 3/8” threads. |
![]() |
T-Handle 909-971 This handle is used to pull the valves from the cylinders, ½” threads. |
![]() |
Valve Puller 600-306 |
![]() |
Puller, Compressor Piston 939-940 |
![]() |
Adapter, Valve Remover 600-329-001 Used to protect compressor rod threads on 2 ½” rods. |
![]() |
Crosshead Nut Wrench 935-351 For removing and installing individual cylinder heads. Attaches directly and quickly to the tapped holes in the cylinder head. No tools are required. The two lifting holes will position the head either level for the inline engines or at an angle for the vee engines.. |
![]() |
Bearing Shell Remover 914-691 Sized to fit in the oil hole of the main bearing journal of the crankshaft. Care must be taken to roll the crankshaft in the correct direction; i.e. not against the bearing tang. This will damage the bearing. This tool can be used on SW and MW compressor frames. |
![]() |
Main Bearing Removal Tool 939-926 Sized to fit in the oil hole of the main bearing journal of the crankshaft. Care must be taken to roll the crankshaft in the correct direction; i.e. not against the bearing tang. This will damage the bearing. This tool can be used on MH/WH compressor frames. |
![]() |
Wrench, Piston Rod 937-391 |
![]() |
Extension Tool 909-975 This tool is used to pull the valve chairs from the cylinders. |
Part Number | Description | RAM Frame |
---|---|---|
600-323 | Valve Removal Bracket (3.25″ Valve Diameter) | X |
600-324 | Valve Removal Bracket (4.00″ Valve Diameter) | X |
600-322 | Valve Removal Bracket (4.875″ Valve Diameter) | X |
600-307 | Valve Removal Bracket (5.75″ Valve Diameter) | X |
600-322 | Valve Removal Bracket (5.25″ Valve Diameter) | X |
600-308 | Valve Removal Bracket (7.00″ Valve Diameter) | X |
600-309 | Valve Removal Bracket (8.00″ Valve Diameter) | X |
600-306 | Valve Removal Tool | X |
600-318 | Main Bearing Removal Tool | X |
600-189 | Crankshaft Seal Expander | X |
904-925 | Rod Insertion Tool | X |
600-187 | Auxiliary Lube Drive Shaft Seal Installer | X |
600-122 | Crosshead Tool Handle | X |
600-188 | Crankshaft Seal Installer | X |
600-121 | Crosshead Tool | X |
600-124 | Spanner Wrench | X |
600-123 | Crosshead Nut Wrench | X |
![]() |
Valve Removal Bracket 600-307 through 600-324 Bracket attaches to the valve to facilitate removal and installation. |
![]() |
Valve Removal Tool 600-306 Handle is used to remove and install the valves. |
![]() |
Main Bearing Removal Tool 600-318 Sized to fit in the oil hole of the main bearing journal of the crankshaft. Care must be taken to roll the crankshaft in the correct direction; i.e. not against the bearing tang. This will damage the bearing. This tool can be used on all 825 engines. |
![]() |
Crankshaft Seal Expander 600-189 Used to expand the crankshaft seal. |
![]() |
Rod Insertion Tool 904-925 This sleeve guides the rod through the seals during installation. |
![]() |
Auxiliary Lube Drive Shaft Seal Installer 600-187 Used to press the lube drive shaft seal into place. |
![]() |
Crosshead Tool Handle 600-122 |
![]() |
Crankshaft Seal Installer 600-188 This tool is used to install the crankshaft seal |
![]() |
Crosshead Tool 600-121 |
![]() |
Spanner Wrench 600-124 |
![]() |
Crosshead Nut Wrench 600-123 |