Part Number Description SW
Frame
MW
Frame
W-7
Frame
W-6
Frame
906-004 Adapter Tool X X    
914-691 Bearing Shell Remover X X   X
939-926 Bearing Shell Remover     X  
S-8384 Compressor Rod Nut Bar X X X X
935-351 Crosshead Nut Wrench X X   X
909-975 Extension Tool X X X X
906-003 Handle for Crosshead X X X  
906-021 Handle for Crosshead       X
939-940 Puller, Compressor Piston     X  
939-978 Starter, Piston Rod – 2 ½” X     X
904-923 Starter, Piston Rod – 2 ¼”       X
904-925 Starter, Piston Rod – 2 ¼”   X    
904-925-003 Starter, Piston Rod – 2 ½”     X  
937-391 Socket, 3” Flats X X X X
S-8228 Socket, 3” Hex X X X X
906-005 Socket, 1 ¾” X X    
939-938 Socket, 1 ¼”     X  
909-973 T-Handle X X   X
909-971 T-Handle X X X X
909-977 Valve Disassembly Tool X X X X
919-541 Valve Ring Clamp X X X X
917-041 Valve Remover X X X X
917-042 Valve Remover     X  
937-391 Wrench, Piston Rod X X X X
S-8676 Wrench, Compressor Nut (12 pt) X X X X
939-994 Wrench, Piston Rod 2 ½”     X  

 

Crosshead Nut Wrench 935-351 For removing and installing individual cylinder heads. Attaches directly and quickly to the tapped holes in the cylinder head. No tools are required. The two lifting holes will position the head either level for the inline engines or at an angle for the vee engines.
Rod Insertion Tool 939-978 This tool is used to install the compressor rod into packing without damaging the seals. This tool is used only on SW frames.
Rod Insertion Tool 904-923 This tool is used to install the compressor rod into packing without damaging the seals. This tool is used only on W-6 frames.
Rod Insertion Tool 904-925 This tool is used to install the compressor rod into packing without damaging the seals. This tool is used only on MW frames.
Rod Insertion Tool 904-925-003 This tool is used to install the compressor rod into packing without damaging the seals. This tool is used only on W-7 frames.
Main Bearing Removal Tool 914-691 Sized to fit in the oil hole of the main bearing journal of the crankshaft. Care must be taken to roll the crankshaft in the correct direction; i.e. not against the bearing tang. This will damage the bearing. This tool can be used on SW and MW compressor frames.
Main Bearing Removal Tool 939-926 Sized to fit in the oil hole of the main bearing journal of the crankshaft. Care must be taken to roll the crankshaft in the correct direction; i.e. not against the bearing tang. This will damage the bearing. This tool can be used on W-7 and W-6 compressor frames.
Handle for Crosshead 906-003 This tool is used to install and remove the crosshead from the crosshead guide. It comes in quantities of two that can be bolted together for storage.
Handle for Crosshead 906-021 This tool is used to install and remove the crosshead from the crosshead guide. It comes in quantities of two that can be bolted together for storage.
Adapter Tool 906-004
Socket 906-005
Wrench, Piston Rod 937-391
Extension Tool 909-975 This tool is used to pull the valve chairs from the cylinders.
T Handle 909-973 This handle is used to pull the valves from the cylinders.
T Handle 909-971 This handle is used to pull the valves from the cylinders.
Valve Disassembly Tool 909-977
Valve Ring Clamp 919-541
Valve Remover 917-041 This tool is used to pull the valve from the cylinder with the threaded female end.
Valve Remover 917-042 This tool is used to pull the valve from the cylinder with the threaded female end.
Puller, Compressor Piston 939-940
Socket 939-938
Socket, 3″ Hex S-8228 Socket with 3” internal hex used to loosen/tighten compressor rod piston nuts with 3” standard hex.
Socket, 3″ Flats 937-391 Socket with 3” internal flats used to loosen/tighten compressor rod piston nuts with 3” flats.
Compressor Rod Nut Bar S-8384 Used to break the compressor rod nuts loose. Bar is heat treated carbon steel. One end fits in 1” dia hole, other end fits in 1.06” dia hole.
Wrench, Compressor Nut (12 pt) S-8676 4” hex-12 pt wrench used to grip the compressor rod nut better.
Wrench, Piston Rod 2 ½” 939-994 Used to loosen/tighten compressor rod from crosshead.
Part Number Description MH WH
906-004 Adapter Tool X X
600-329-001 Adapter, Valve Remover X X
914-691 Bearing Shell Remover X X
S-8384 Compressor Rod Nut Bar X X
935-351 Crosshead Nut Wrench X X
909-975 Extension Tool X X
939-926 Main Bearing Removal Tool X X
620-116-001 Protector, Rod X X
939-940 Puller, Compressor Piston X X
909-973 T-Handle X X
909-971 T-Handle X X
600-306 Valve Puller X X
S-8676 Wrench, Compressor Nut (12 pt) X X

 

Compressor Rod Nut Bar S-8384 Used to break the compressor rod nuts loose. Bar is heat treated carbon steel. One end fits in 1” dia hole, other end fits in 1.06” dia hole.
Wrench, Compressor Nut (12 pt) S-8676 4” hex-12 pt wrench used to grip the compressor rod nut better.
Adapter Tool 906-004
T-Handle 909-973 This handle is used to pull the valves from the cylinders, 3/8” threads.
T-Handle 909-971 This handle is used to pull the valves from the cylinders, ½” threads.
Valve Puller 600-306
Puller, Compressor Piston 939-940
Adapter, Valve Remover 600-329-001 Used to protect compressor rod threads on 2 ½” rods.
Crosshead Nut Wrench 935-351 For removing and installing individual cylinder heads. Attaches directly and quickly to the tapped holes in the cylinder head. No tools are required. The two lifting holes will position the head either level for the inline engines or at an angle for the vee engines..
Bearing Shell Remover 914-691 Sized to fit in the oil hole of the main bearing journal of the crankshaft. Care must be taken to roll the crankshaft in the correct direction; i.e. not against the bearing tang. This will damage the bearing. This tool can be used on SW and MW compressor frames.
Main Bearing Removal Tool 939-926 Sized to fit in the oil hole of the main bearing journal of the crankshaft. Care must be taken to roll the crankshaft in the correct direction; i.e. not against the bearing tang. This will damage the bearing. This tool can be used on MH/WH compressor frames.
Wrench, Piston Rod 937-391
Extension Tool 909-975 This tool is used to pull the valve chairs from the cylinders.
Part Number Description RAM Frame
600-323 Valve Removal Bracket (3.25″ Valve Diameter) X
600-324 Valve Removal Bracket (4.00″ Valve Diameter) X
600-322 Valve Removal Bracket (4.875″ Valve Diameter) X
600-307 Valve Removal Bracket (5.75″ Valve Diameter) X
600-322 Valve Removal Bracket (5.25″ Valve Diameter) X
600-308 Valve Removal Bracket (7.00″ Valve Diameter) X
600-309 Valve Removal Bracket (8.00″ Valve Diameter) X
600-306 Valve Removal Tool X
600-318 Main Bearing Removal Tool X
600-189 Crankshaft Seal Expander X
904-925 Rod Insertion Tool X
600-187 Auxiliary Lube Drive Shaft Seal Installer X
600-122 Crosshead Tool Handle X
600-188 Crankshaft Seal Installer X
600-121 Crosshead Tool X
600-124 Spanner Wrench X
600-123 Crosshead Nut Wrench X

 

Valve Removal Bracket 600-307 through 600-324 Bracket attaches to the valve to facilitate removal and installation.
Valve Removal Tool 600-306 Handle is used to remove and install the valves.
Main Bearing Removal Tool 600-318 Sized to fit in the oil hole of the main bearing journal of the crankshaft. Care must be taken to roll the crankshaft in the correct direction; i.e. not against the bearing tang. This will damage the bearing. This tool can be used on all 825 engines.
Crankshaft Seal Expander 600-189 Used to expand the crankshaft seal.
Rod Insertion Tool 904-925 This sleeve guides the rod through the seals during installation.
Auxiliary Lube Drive Shaft Seal Installer 600-187 Used to press the lube drive shaft seal into place.
Crosshead Tool Handle 600-122
Crankshaft Seal Installer 600-188 This tool is used to install the crankshaft seal
Crosshead Tool 600-121
Spanner Wrench 600-124
Crosshead Nut Wrench 600-123